easyE-60i – Usable almost everywhere

The new inline actuators from Bansbach can now do significantly more! They not only impress with their slim design in combination with very high forces. The integration of the controller in the actuator opens up countless new possibilities for you.

Speed and force
Connecting parts

Type 60

The 60 series is also available as easyE-60i, the intelligent inline actuator solution with integrated controller. And that with forces of up to 10000N. Without compromising on design and efficiency.

The integration of the controller results in the following advantages:
  • Very compact design despite integrated controller
  • Easy installation and maintenance free
  • Software for easy setup
  • Internal stroke limitation
  • Adjustable current limit
  • Internal heat protection
  • Industrial interface MODBUS RTU on RS485
  • Adjustable start ramp
  • Adjustable stop ramp
  • Plug & Play solution with iConnect-Box
  • Stroke: 50, 100, 150, 200, 250, 300, 350, 400, 500 and 750mm (others on request)
  • Materials:
  • Motor and actuator tube are powder coated steel or stainless steel
  • Piston rod is stainless steel
  • Front and rear brackets are aluminium or stainless steel
  • Protection class: IP66 (standard), harsh environment (according to IP68 and IP69)
  • Temperature:
  • Operation: -20°C to +50°C
  • Storage: -40ºC to +70ºC
  • Cable: Cores: 2 x AWG16 + 6 x AWG 26, Ø = 6,8 mm, black jacket, Molex Mini-Fit Jr. 8 pin or similar.
  • Bending radius: 15x cable diameter
  • Max. static load/Self locking force: 18.100N, depending on stroke length for push-applications
  • Duty cycle: Max. 10% or 2 minutes in use followed by 18 minutes rest

The integrated control is offered in 6 versions.

All have one MODBUS-RTU system based on RS485:

    Simple control to move the actuator up and down. In combination with the iConnect-Box, it develops into a plug-and-play solution. Just plug in and run
    This controller also outputs an analog position signal (0V-5V or 0V-10V)
    This controller is operated completely via Modbus-RTU RS485
    Compared to the SDB controller, this controller also emits a Hall signal
    With this controller, a specific position can be controlled via an analog voltage signal
    With this controller, up to 8 actuators can easily be operated synchronously
Speed and force

Speed and force


24VDC (28VDC) – Current at maximum load: 11,5A

 Gear ratio
  • Force (dyn. push and pull) [N]
  • Speed at maximum load [mm/s]
  • 1900
  • 26
  • 4300
  • 12
  • 6600
  • 8
  • 8100
  • 6
  • 10000
  • 5

Max. load limited for stroke length > 400mm: 5000N



  • Hub + 373*
Clevis rear
  • +15
Harsh Environment
  • +25

*If stroke >400mm: EL+25mm (not Harsh-Environment version)

Axial backlash: +/- 0,5mm, generally length tolerance +/- 1mm

Weight of the actuators:

  • Stroke [mm]
  • Weight [kg]
  • 50
  • 4,1
  • 100
  • 4,4
  • 150
  • 4,7
  • 200
  • 5
  • 250
  • 5,3
  • 300
  • 5,6
  • 350
  • 5,9
  • 400
  • 6,2
  • 500
  • 6,8
  • 750
  • 7,6

The weight may vary depending on the options and versions selected.

Connecting parts

Bansbach connecting parts

Choose your connecting part.
Ø mm
L5 mm
SW mm
A mm
Edelstahl (316)
Max. Load [N]

Bansbach Brackets

Here you will find our brackets for the easE-60i.

Cable i-connect
easyE-i handset
easyE-i power supply
easyE -i programming cable
I-connect box
I-connect-box din

How to commission your electric actuator

Commissioning EasyE-i

Programming the control



Software easyE-i

Do you need help?
We are there for you

Contact person
At Bansbach easylift

the product is precisely adapted to your requirements in order to ensure optimal function. We are happy to support and advise you in the selection of the right product.

With our “Technical Support” you have a direct line to our technicians, who will competently assist you. If you have any questions about offers, availability or prices, our commercial support will be happy to assist you.

Step by step to the individual product

We build your gas spring!

The Bansbach gas spring configurator offers

you the possibility to put together your individual

gas spring from various components

even more easily and quickly.

Bansbach easylift

Stainless steel – Products
  • » High-quality stainless steel material (V4A, AISI No. 316L)
  • » Water resistant
  • » Suitable for food, chemical and seawater applications
  • » Connecting parts also made of stainless steel
more information

Applications examples

Here you will find our products.


Are Bansbach gas springs ROHS compliant?

Yes, they are fully ROHS compliant and also meet all guidelines, export/import regulations and goals of other company programs that we are aware of.

Can a gas spring made to customer specifications be returned?

Bansbach gas springs are manufactured to order – from mostly stock components. Cancellation, exchange or return is therefore not possible.
In case of free delivery, we will gladly take over the disposal – without charge – for you.

Can gas springs be disposed of in household waste?

No, gas springs are mainly made of metal. Please observe our disposal instructions.

Can gas springs be used in the food industry?

With the high-quality stainless steel gas springs in V4A, the high requirements of the food industry are met. Food-grade oil (FDA oil) is optionally available.

Can the speed/damping of the gas spring be influenced?

By selecting the appropriate nozzle bore and oil viscosity, the speed and damping of the gas spring can be adapted to the application.

Do Bansbach gas springs have to be stored with the piston rod pointing downwards?

Bansbach gas springs can be stored in any position.

Does a gas spring need to be protected from dirt?

The piston rod must be protected against impact, scratches and contamination – especially paint application. Damage to the surface will destroy the sealing system. If necessary, a wiper or a protective tube should be provided.

Does a gas spring need to be serviced?

No, Bansbach gas springs are maintenance-free. The piston rod must not be greased or oiled.

How do I find my personal contact person?

Bansbach easylift GmbH
Bararossastrasse 8
D-73547 Lorch
Phone: +49 (0) 7172/9107-0
Fax: +49 (0) 7172/9107-44
E-Mail: info@bansbach.de

You can find a contact person on site
 Contact form

How high can the internal pressure of a gas spring be?

Depending on the series and the desired extension force, this can be up to approx. 300 bar.

How much is the weight of a gas spring?

Due to the wide range of products, the weights vary greatly.

Diameter piston rod / cylinder:
Ø3/8; Ø4/12; Ø6/15; Ø6/19; Ø6/22; Ø8/19; Ø8/22

100 g – 500 g

Diameter piston rod / cylinder:
Ø8/28; Ø10/22; Ø10/28; Ø12/28; Ø14/28

200 g – 1000 g

Diameter piston rod / cylinder:
Ø16/28; Ø10/40; Ø12/40; Ø14/40; Ø20/40; Ø30/70

500 g – 8000 g

In which colors are Bansbach gas springs available?

The piston rod and the cylinder are supplied in black (standard).

On request, our cylinders are available in all RAL colors. Exception: stainless steel

In which temperature ranges can Bansbach gas springs be used?

For ambient temperatures from -30°C to +80°C.
For other temperature ranges (down to -55°C or up to +200°C) special seal sets are available.

Is it possible to repair a gas spring?

No, because it is a closed system that is under high pressure and must not be opened.

Is the extension force of the gas spring temperature-dependent?

For physical reasons, the extension force of the gas spring changes by approx. 3.3% per 10°C (base + 20°C).

What does the index number (e.g. – -001/100 N) at the end of the article designation of the gas spring mean?

This is a code assigned internally by Bansbach for unambiguous reproducibility of the gas spring.

What materials are Bansbach gas springs made of?

Gas springs consist of piston rod, cylinder tube, connecting parts, turned parts, seals, oil, grease and nitrogen. Piston rods and cylinder tubes are made of steel and are CeramPro® or powder coated in our company. Connecting parts and turned parts are made of lead-free steel or lead-free aluminum.

Seals, oils, greases do not contain substances that are on the list of critical or hazardous substances. Nitrogen is an inert gas that neither burns nor poses any other health hazards. Bansbach gas springs therefore comply with current and, as far as we know, planned laws and regulations.

They comply for example with the RoHS Directive, WEEE Directive, Directives 2003/11/EC, 2002/95/EC, 2002/96/EC. They are not covered by Directives 94/9/EC, 97/23/EC, and 98/37/EC, nor by UN 3164, TRGS 220, and UL 60601-1.

Verification that Bansbach gas springs in the end product comply with national or international laws and regulations remains the responsibility of our customers or the user.

What service life/running performance can I expect from a Bansbach gas spring?

On average, Bansbach gas springs are designed for 50,000 – 100,000 double strokes.
Depending on the design, installation and effective stroke, several 100,000 strokes can also be achieved.
For other products please contact us.

Which stroke lengths are possible for the gas springs?

Depending on the series and design of the gas spring, the stroke length can be freely selected between 10 mm and 1000 mm. Other variations possible, please contact us.


We are there for you.
+49 (0)7172 / 9107-0

With our “Technical Support” you have a direct line to our technicians, who will competently assist you. If you have questions about offers, availability or prices, our commercial support will be happy to assist you.